01902 636106
Engineering Solutions for Engineering Problems
Established in  1981
Engineering Solutions for Engineering Problems
Established in 1981
© Designed and Coded by Bits and PCs 

Machine

Design, Modification & Overhaul

Overhauling and modification of your existing machinery is no problem. We can strip your machine, manufacture new parts to replace worn ones, modify the machine to your new requirements, guard your machine to make it safe, alter your machine to take account of a new processes, supply and replace all worn components such as; pneumatics, hydraulics electrics, bearings and seals. We can either arrange transport to collect your machine for us to complete the work at our works or we can complete the work on your site at a time of your choosing. Once the machine is complete we can then arrange to install and commission the unit. If it is a new machine you require or a copy of an existing one then we can also help. We can arrange a site visit with our engineers to discuss your requirements.
Oil-scale cabinet - Again fully manufactured by Sprint. This is an insulated cabinet that has electric heaters in to keep the weighed oil fluid. The fabricated stainless steel vessels weigh the liquid for discharge in to a mixer via pneumatically operated valves and 3 phase pumps
Here we have repaired the hinge on a lid of an aircraft tyre press. The fabrication was straightened and strengthened with thicker plates. The hydraulic cylinder overhauled and the bearing bushes and shaft replaced.
Before and after pictures of an Ingot conveyor refurbishment for a non-ferrous casting company. The unit was stripped, shot blast, repaired and strengthened. All moving parts were machined and replaced. the motor gear unit was overhauled including new bearings and seals. Finally the unit was painted.
Above two components; a gear and a shear blade manufactured for the complete unit below. All machined and built by Sprint. This assembly wraps steel wire around bales of cans on an MRF Baler machine.
Ladder storage. A wall mounted unit to enable sets of ladders to be stored and securely locker up. Manufactured for the aerospace industry.
Component porosity testing machine - pneumatically controlled: This machine has been built to batch test the porosity of cast bronze components. It is completely pneumatically operated and controlled. 
The Pneumatic cabinet that controls the valves on the oil-scale cabinet
Ball-screw and precision bearing change in Key cutting xyz head. Here we stripped the unit down and supplied and replaced the precision ball-screw bearings and linear slides. The unit was then rebuilt. 
A rubber stock chopping machine fabricated, machined and built by Sprint. All parts of this heavy duty rubber chopper were manufactured and fabricated by Sprint at our works.
01902 636106
Engineering Solutions for Engineering Problems
Established in  1981

Machine

Design, Modification & Overhaul

Overhauling and modification of your existing machinery is no problem. We can strip your machine, manufacture new parts to replace worn ones, modify the machine to your new requirements, guard your machine to make it safe, alter your machine to take account of a new processes, supply and replace all worn components such as; pneumatics, hydrauLics electrics, bearings and seals. We can either arrange transport to collect your machine for us to complete the work at our works or we can complete the work on your site at a time of your choosing. Once the machine is complete we can then arrange to install and commission the unit. If it is a new machine you require or a copy of an existing one then we can also help. We can arrange a site visit with our engineers to discuss your requirements.
Oil-scale cabinet - Again fully manufactured by Sprint. This is an insulated cabinet that has electric heaters in to keep the weighed oil fluid. The fabricated stainless steel vessels weigh the liquid for discharge in to a mixer via pneumatically operated valves and 3 phase pumps
Here we have repaired the hinge on a lid of an aircraft tyre press. The fabrication was straightened and strengthened with thicker plates. The hydraulic cylinder overhauled and the bearing bushes and shaft replaced.
Before and after pictures of an Ingot conveyor refurbishment for a non-ferrous casting company. The unit was stripped, shot blast, repaired and strengthened. All moving parts were machined and replaced. the motor gear unit was overhauled including new bearings and seals. Finally the unit was painted.
Above two components; a gear and a shear blade manufactured for the complete unit below. All machined and built by Sprint. This assembly wraps steel wire around bales of cans on an MRF Baler machine.
Ladder storage. A wall mounted unit to enable sets of ladders to be stored and securely locker up. Manufactured for the aerospace industry.
Component porosity testing machine - pneumatically controlled: This machine has been built to batch test the porosity of cast bronze components. It is completely pneumatically operated and controlled. 
The Pneumatic cabinet that controls the valves on the oil-scale cabinet
Ball-screw and precision bearing change in Key cutting xyz head. Here we stripped the unit down and supplied and replaced the precision ball-screw bearings and linear slides. The unit was then rebuilt. 
A rubber stock chopping machine fabricated, machined and built by Sprint. All parts of this heavy duty rubber chopper were manufactured and fabricated by Sprint at our works.
© Designed and Coded by Bits and PCs
Overhauling and modification of your existing machinery is no problem. We can strip your machine, manufacture new parts to replace worn ones, modify the machine to your new requirements, guard your machine to make it safe, alter your machine to take account of a new processes, supply and replace all worn components such as; pneumatics, hydraulics electrics, bearings and seals. We can either arrange transport to collect your machine for us to complete the work at our works or we can complete the work on your site at a time of your choosing. Once the machine is complete we can then arrange to install and commission the unit. If it is a new machine you require or a copy of an existing one then we can also help. We can arrange a site visit with our engineers to discuss your requirements.
Oil-scale cabinet - Again fully manufactured by Sprint. This is an insulated cabinet that has electric heaters in to keep the weighed oil fluid. The fabricated stainless steel vessels weigh the liquid for discharge in to a mixer via pneumatically operated valves and 3 phase pumps
Here we have repaired the hinge on a lid of an aircraft tyre press. The fabrication was straightened and strengthened with thicker plates. The hydraulic cylinder overhauled and the bearing bushes and shaft replaced.
Before and after pictures of an Ingot conveyor refurbishment for a non-ferrous casting company. The unit was stripped, shot blast, repaired and strengthened. All moving parts were machined and replaced. the motor gear unit was overhauled including new bearings and seals. Finally the unit was painted.
Above two components; a gear and a shear blade manufactured for the complete unit below. All machined and built by Sprint. This assembly wraps steel wire around bales of cans on an MRF Baler machine.

Machine Design

Modification & Overhaul

Ladder storage. A wall mounted unit to enable sets of ladders to be stored and securely locker up. Manufactured for the aerospace industry. Ball-screw and precision bearing change in Key cutting xyz head. Here we stripped the unit down and supplied and replaced the precision ball-screw bearings and linear slides. The unit was then rebuilt.
A rubber stock chopping machine fabricated, machined and built by Sprint. All parts of this heavy duty rubber chopper were manufactured and fabricated by Sprint at our works.
Component porosity testing machine - pneumatically controlled: This machine has been built to batch test the porosity of cast bronze components. It is completely pneumatically operated and controlled. 
The Pneumatic cabinet that controls the valves on the oil-scale cabinet
01902 636106
01902 636106
Engineering Solutions for Engineering Problems
Established in  1981

Machine

Design, Modification & Overhaul

Overhauling and modification of your existing machinery is no problem. We can strip your machine, manufacture new parts to replace worn ones, modify the machine to your new requirements, guard your machine to make it safe, alter your machine to take account of a new processes, supply and replace all worn components such as; pneumatics, hydraulics electrics, bearings and seals. We can either arrange transport to collect your machine for us to complete the work at our works or we can complete the work on your site at a time of your choosing. Once the machine is complete we can then arrange to install and commission the unit. If it is a new machine you require or a copy of an existing one then we can also help. We can arrange a site visit with our engineers to discuss your requirements.
Oil-scale cabinet - Again fully manufactured by Sprint. This is an insulated cabinet that has electric heaters in to keep the weighed oil fluid. The fabricated stainless steel vessels weigh the liquid for discharge in to a mixer via pneumatically operated valves and 3 phase pumps
Before and after pictures of an Ingot conveyor refurbishment for a non-ferrous casting company. The unit was stripped, shot blast, repaired and strengthened. All moving parts were machined and replaced. the motor gear unit was overhauled including new bearings and seals. Finally the unit was painted.
Above two components; a gear and a shear blade manufactured for the complete unit below. All machined and built by Sprint. This assembly wraps steel wire around bales of cans on an MRF Baler machine.
Ladder storage. A wall mounted unit to enable sets of ladders to be stored and securely locker up. Manufactured for the aerospace industry.
Component porosity testing machine - pneumatically controlled: This machine has been built to batch test the porosity of cast bronze components. It is completely pneumatically operated and controlled. 
The Pneumatic cabinet that controls the valves on the oil-scale cabinet
Ball-screw and precision bearing change in Key cutting xyz head. Here we stripped the unit down and supplied and replaced the precision ball-screw bearings and linear slides. The unit was then rebuilt. 
A rubber stock chopping machine fabricated, machined and built by Sprint. All parts of this heavy duty rubber chopper were manufactured and fabricated by Sprint at our works.
© Designed and Coded by Bits and PCs
Here we have repaired the hinge on a lid of an aircraft tyre press. The fabrication was straightened and strengthened with thicker plates. The hydraulic cylinder overhauled and the bearing bushes and shaft replaced.